Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.
Min. Shipping :£0.00
VAT (20%): £0.00
Total: £0.00
Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.
Min. Shipping :£0.00
VAT (20%): £0.00
Total: £0.00
High quality protective grille for Land Rover lights part number 300A, 300CA, 300LC and 300ST (Land Rover part numbers RTC5013, RTC5012, RTC5523) as well as the S60 series part number LED upgrade...
High quality protective grille for Land Rover 95mm diameter NAS type LED lights - part numbers S6079LED, S6080LED and S6087LED as well as LED Upgrade light sets LRLEDKIT2 and LRLEDKIT4
Reproduction frosted plastic lens for Lucas LD109 type side lamps. Will fit original lamps as well as our 918-R, 918-RB and 918-T part numbered reproduction lamps.
Return spring for dipping reflectors used on Lucas lamps including the L150. Extension spring. 48mm long, 6.25mm diameter with one closed loop end and one open loop end. Please check dimensions...
Long daisy head head and spot lamp rim screw for some large Lucas headlamps including the P80, overall length 49mm (head 29mm, thread 20mm) head diameter 15mm tapering down to 9mm, with a 2BA...
Dipping reflector pivot used on Lucas two piece dipping reflectors. Spring steel 'P' clip and ball bearing holds inner refector bowl and outer reflector rim togther, allowing the inner reflector...
Compression spring for use with long rim catch part no. 863A. The spring is held in place by a small roll pin inserted through the end of the catch). Makes Lucas part no assembly 532590
Knurled and slotted headlamp rim screw for Lucas L140, L150 etc. type headlamps. Overall length 33mm (head 9mm, thread length 24mm), head diameter 10mm. 2BA thread. Chrome plated brass. Offered as...
Headlamp EPDM rim seal for many Lucas lamps including the L140, L148, L150 and L165 and L166. The flap locates in the 3mm wide groove in the bowl rim, behind where the reflector (bead type, rather...
Two piece spun brass assembly, to replace damaged BA15 bulb holder sockets on vintage lamp reflectors. Remove old damaged bulb holder socket and then press fit new assembly together either side of...
Hiqh quality clamp for tightening the bulb holder socket in the back of Lucas lamp refectors onto BA15 bulb holders (e.g. our part numbers 853 or 153). The clip strap is formed from steel and...
High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLT kit but ompatible with many other headlamp stem bolts. Black half gloss powder coated finish of machined part. Good...
High quality stem bolt cup for headlamp mounting. Companion part to STEMBOLTKIT but compatible with many other headlamp stem bolts. Chrome finish of machined part. Good weight and finish. 38mm max...
Chrome plated bronze bracket for Lucas type headlamps such as the L140. Fits through a slot in the headlamp rim, and the base of the daisy headed rim fixing screw (part number 641) locates in the...
Chome plated bronze bracket for Lucas type headlamps such as the L140. Fits inside the headlamp shell rim - the tongue fits through the slot which then accepts the rim fixing screw 641 in a 2BA...
Silver painted bronze bracket for some Lucas type headlamps. Fits inside headlamp shell, the tongue fits through rim slot which then accepts a rim fixing screw through a plain 5mm diameter hole,...
Silver painted bronze bracket. Fits inside headlamp rim, tongue fits through rim slot which then accepts rim fixing screw. Dimensions 36mm x 18mm, screw tongue 17mm wide x 15mm tall with 5mm slot.
Silver painted bronze bracket. Fits inside headlamp rim, the tongue fits through the rim slot which then accepts rim fixing screw. Dimensions 36mm x 13mm, screw tongue 17mm wide x 13mm tall with...
Main rim gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Number plate lens gasket for our 211R series split lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Highly polished stainless steel lamp rim, for split lens red/red or red/amber 'Duolamps' (our part number series 211RR/RA)
Orange plastic semaphore arm lens to fit the Lucas SF80 trafficator, part of the SE100 trafficator assembly. Equivalent to Lucas part number 532026. Overall length 180mm.
Polished stainless steel backing cover for Lucas SF80 SE100 trafficator. overall length 195mm.
Plated dish reflector to assist with light reflection in rubber divers lamp, overall diameter 55mm with 14mm hole in the centre.
Rubber rear body (boot) for Lucas L488 model type lamps. Ford part reference E0A-13216.
Rubber rear body (boot) for Lucas L594 model type lamps.
Rubber lens 'O' ring seal for Lucas 1130 type sidelamps (297 series lamps) fitted with the plastic lens (part number 361).
Rubber lens 'O' ring seal for Lucas type 1130 (297 series) sidelamps, with the glass lens with chrome surround and rim (part number 681).
Stainless steel lamp housing retaining screw - 4BA thread x 16mm long. Slotted and knurled head, 8mm diameter. Used on D lamps to secure the lamp housing to the back plate.
Black powder coated cover for 550 TYPE Number Plate Lamp "FROGEYE" Used on Triumphs & GT40 MK1 cars . Cowled black powder coated surround 48mm x 35mm with two mounting holes at 42mm hole centres
Chrome cover for 550 TYPE Numpber Plate Lamp "FROGEYE" Used on Triumphs & GT40 MK1 cars . Cowled chrome surround 48mm x 35mm with two mounting holes at 42mm hole centres
Replacement side mounting bracket for the pillar mounted Raydyot spotlamp. approx 106mm overall, chrome on brass.
Replacement rubber base gasket for Lucas L471 type rear lamps
Black moulded rear boot housing for Lucas L489 type side lamps
Glass to rim seal ring
Chrome lamp rim, glass lens and retaining seal for L489 lamp
Replacement chrome plated lamp retaining rim for Lucas L471 type rear lamps
Fitted to the head lamp units we assemble, BS specified wiring and wire colours. Approximate length 45cm. Single H4 lamp connector block with wired brass flag terminals, wires encased in sleeve...
Rubber lamp entry cable grommet. Approximately 13.5mm internal diameter.
Headlamp mounting bolt - hollow. Thread 5/8" x 26 tpi (fine thread) as the original item. measures approx 56mm long x 16mm thread diameter.
Headlamp mounting bolt - hollow, with loose collar. Thread 5/8" x 26 tpi (fine thread) as original item. Measures approx 50mm long x 16mm thread diameter.
Headlamp mounting bolt - hollow, used on Butler type lamps. Thread 5/8" x 26 tpi ( ine thread). Measures approx 68mm long x 16mm thread diameter.
Headlamp mounting bolt - hollow, used on many CAV type lamps. Thread 5/8" x 26 tpi (fine thread) as original item. Measures approx 50mm long x 16mm thread diameter.
Headlamp mounting bolt and nut for Lucas P100 type lamps. Thread 1/2" x 26 tpi (fine thread) as original item. Measures approx 105mm long x 13mm thread diameter (thread runs for 28mm), head...
Lamp mounting bolt - hollow. Thread 7/16" x 26 tpi (fine thread) as original. Measures approx 36mm long x 11mm thread diameter. Supplied with hexagon nut. Used on various Lucas spot and sidelamps.
Hexagonal brass nut for headlamp, 5/8" x 26 tpi (fine thread). Approx 16mm bore. 10mm deep. 13/16" AF.
Hexagonal nut for many Lucas type sidelamps. 7/16" x 26 tpi (very fine thread) approx 11mm bore.
Brass headlamp stud mounting nut for Lucas RB160, P100, P80 etc. type lamps. Thread 1/2" x 26 tpi. Equivalent to Lucas part number 500357
Daisy head headlamp rim screw for the Lucas L140 & L150 headlamps, overall length 36mm (head 18mm, thread 18mm) head diameter 15mm tapering down to 9mm, with a 2BA thread. Chrome plated brass.
Lamp glass clip. 'W' wire clip to hold the glass into a headlamp rim - approx 36mm long. Most rims about 8" diameter use four.
Lamp glass clip. Large 'W' wire spring clip for holding glass lenses into headlamp rims. Approx 48mm long side with a slight curve. Useful for deep headlamp rims. Most headlamp rims use four.
Lamp glass clips. Large 'W' wire for holding glass lenses into headlamp rims, approx 54mm long side. This clip can be used for other applications but is actually made for P100 R & S type lamps.
Lamp glass clips. Small 'W' wire clip for holding lenses into rims in sidelamps. Approximately 22mm long, sold as a packet of 6 pieces
Flat, rubber mounting pad for 297 (Lucas 1130) type sidelamps.
Body to base gasket for Lucas type ST51 'D' Lamps - our part number series, 428, 249 and CA1149
Lens retaining wire for 249/428 part number series (equivalent to Lucas type ST51 type) 'D' lamps
Rubber mounting pad for our 787 (Lucas 516 type) sidelamp, dimensions 50mm long, 30mm wide, 14mm tall with 12mm hole.
Chrome on bronze rim catch for Lucas head lamps, long type, overall dimensions 45mm long x 26mm wide. Makes Lucas assembly part no. 532590 with compression spring - part number 864A - and a small...
Chromium plated rim catch, for Lucas type head lamps, short style, overall dimensions 31mm long x 27mm wide, equivalent to original Lucas part number 509936. Use with 'spectacle' wire spring clip...
Spring (spectacle shape) for rims that use short rim catch clip (our 863B), equivaent to Lucas part number 509191
Top rim stainless steel retaining screw for 297 (Lucas 1130 type) sidelamp lenses - use to retain lens part numbers 681 (glass with chrome surround) and 361C/361A (clear or amber moulded plastic).
Mounting bracket (with rubber pad and bolts) for mounting 211/958 part number series 'Duolamp' type lamps away from wing. Chromium plated. Available for left or right of car. Measurement along the...
Mounting bracket (with rubber pad and bolts) for mounting 211/958 part number series 'Duolamp' type lamps away from wing. Chromium plated. Available for left or right of car. Measurement along the...
Mounting bracket (with rubber pad and bolts) for mounting 211/958 part number series 'Duolamp' type lamps away from wing. Chromium plated. Available for left or right of car. Measurement along the...
A pair of resistors to be used with LED Indicators. One needed for each LED indicator to prevent rapid 'hyper' flashing if not using an LED flasher unit. Resistor size is 20mm x 20mm, Mounting...
12 volt single contact BA9S 23 watt amber bulb. dimensions 9mm wide x 26mm tall with 9mm diameter cap, ideal for use when changing a sidelight fitted with a BA9 bulb into an indicator lamp - as...
Glass lens in golden amber for divers lamp. Used in our CA1177. 53mm diameter stained glass
Glass lens in clear for divers lamp. Used in our CA1177. 53mm diameter stained glass
Glass lens in red for divers lamp. Used in our CA1177. 53mm diameter stained glass
Number plate lens gasket for our CA1265/1266 series single lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Main rim gasket for the CA1265 series single, symmetrical lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Highly polished stainless steel lamp rim for single (equal waisted) 'Duolamp' type lamps (our part number series CA1265)
Main rim gasket for the CA1266 series single, non-symmetrical lens 'Duolamp' type lamps. Made of quality cork material. Die cut to the exact shape and size as original to provide a nice tight seal.
Highly polished stainless steel lamp rim for single (unequal, waisted) lens 'Duolamp' type lamps (our part number series CA1266)
Butler type headlamp screw/stud and catch barrel/boss.
Stainless steel headlamp rim retaining screw, for use with E1ADKN-13050
Used in Butler type lamps - stainless steel. Use with E1ADKN-13047
We have designed this backing plate to reduce light loss into the boot of a Cobra, therefore increasing the light output of L542 type lamps.
Base rubber for L691 Lucas type lamps. Fits between the lamp base and the wing. Lucas part number 54572755
L691 screw kit. 2 cross head screws and 2 ferrules
Conversion kit to modify your 776 part number or Lucas ST38/'Pork Pie' type rear lamps to also give amber turn indication. New WEDGE T10 bulbs and bulb holders, special red and amber lens. This...
Stem bolt, shakeproof washer and nut used in free standing headlights such as our 5 3/4" 1267 and and 7" AS700 part number series lamps. Excudes cup mount - please see part numbers STEMBOLTCUPB...